Aeroseal duct sealing in Metro Detroit usually costs between $600 and $4,500 for a whole-house job. Most homeowners pay between $1,200 and $2,800, depending on home size and how much duct leakage needs to be sealed.
The final price depends on your home’s square footage, the number of duct runs, and how easy it is to access the ductwork. Smaller homes with simple systems cost less, while larger homes with long or hard-to-reach ducts cost more.
If you’re comparing bids, the main price factors are the amount of initial leakage, the number of supply and return registers, and how difficult it is to access the ductwork. The following guide explains what drives Aeroseal cost, what to look for in an itemized quote, and how to decide if this solution fits your home.
Typical Price Ranges for a Home
Aeroseal cost mainly scales with home size, square footage, and the number of duct branches. A single-zone system with moderate leakage costs less to seal than a multi-story home with complex ductwork and high leakage.
Small and Straightforward Systems
A smaller home (1,200–1,500 square feet) with a single-zone system and accessible ductwork typically costs $800 to $1,400 for a whole-house Aeroseal job. These homes usually have six to eight supply ducts and one or two returns, keeping labor to two or three hours.
Leakage in these systems is often lower, so the crew spends less time sealing gaps.
Average Homes With Moderate Leakage
Most Metro Detroit homes are 1,800 to 2,800 square feet with moderate duct leakage and a mix of easy and tricky access points. Expect to pay $1,500 to $3,000 for this size and scope.
These jobs usually take three to five hours and include before-and-after testing to confirm leakage reduction.
Large or Complex Duct Systems
Larger homes over 3,000 square feet with multi-zone systems, long duct runs, or finished basements often cost $3,000 to $4,500. High initial leakage, many duct connections, and extended labor hours all add to the price.
Older or poorly insulated ducts may need a second sealing pass, which raises the cost further.
What an Itemized Estimate Should Include
A reliable Aeroseal quote breaks down the job into clear line items. You should see separate charges for diagnostic testing, labor, sealant and equipment, and any warranty coverage.
Testing and Pre-Inspection Charges
Every Aeroseal job starts with a pre-inspection and diagnostic testing to measure leakage, usually with a blower door or duct pressurization test. This step adds $100 to $400 and gives you a baseline for comparison after the work is done.
Skipping this step means you won’t know how much leakage was actually reduced.
Labor, Equipment, and Sealant
Labor is the largest part of most quotes, often $400 to $2,000 depending on job length and local rates. Equipment fees usually run $100 to $600.
Sealant material costs are typically included in the total price, but confirm this with your contractor.
Repairs, Permits, and Warranty Coverage
If your ducts have large tears, disconnected sections, or crushed runs, repairs must be done before sealing and should be listed separately. Permits are rarely required for duct sealing alone but may be needed if the job includes other HVAC work, adding $50 to $150.
Ask about warranty options. Many contractors offer a follow-up visit or warranty on leakage reduction, which can add $100 to $350 to the quote.
Factors That Raise or Lower the Final Quote
Several details specific to your home can push the price up or down. Duct length, layout, and accessibility all play a role, as does the severity of leakage.
Duct Size, Length, and Layout
Longer duct runs and more branches increase the total footage to seal. Homes with duct runs over 60 feet often need more sealant and longer testing.
A simple layout with straight runs costs less to seal than a system with many turns and feeder lines.
Access Through Attics, Crawlspaces, and Finished Areas
Duct accessibility affects labor time. Open attics or unfinished basements make the job faster.
Cramped crawlspaces, low-clearance attics, or ducts hidden behind finished ceilings require more time and increase labor costs.
Leak Severity and System Condition
Homes with high leakage need more sealant and longer machine run time. Older duct systems with visible gaps or disconnected sections often require manual repair before Aeroseal can start, adding to the cost.
When Aeroseal Is the Right Solution
Aeroseal duct sealing works well for certain types of leaks but isn’t a fix for every duct problem. Knowing which issues it can address helps you avoid paying for a service that won’t solve your problem.
Leaks That Can Be Sealed From Inside the Ducts
Aeroseal is designed to close small to medium gaps, seams, and pinholes throughout a duct network, including areas that can’t be reached with mastic or tape. The process pressurizes the ductwork and uses sealant particles to plug these openings from the inside.
This makes Aeroseal especially useful for ducts buried in walls, floors, or tight attic spaces.
Damage That Requires Manual Repair First
Large tears, fully disconnected duct sections, or crushed runs must be repaired before Aeroseal can work. A technician inspects the system and flags damage that needs manual patching before scheduling the sealing.
Homeowner Preparation Versus Licensed HVAC Work
You can help by clearing attic access points, moving items away from crawlspace entries, and making sure your furnace and duct system are accessible. The actual sealing, testing, and any duct repair should be handled by a licensed HVAC technician.
Comparing Local Quotes and Planning the Project
Get quotes from several Metro Detroit contractors and compare what’s included in each bid. Local labor rates, job duration, and how each company documents leakage reduction matter more than just the bottom-line price.
Metro Detroit Labor and Scheduling Considerations
Labor rates for Aeroseal work in southeast Michigan are close to the national average. Scheduling is tighter during peak heating and cooling seasons.
Booking in late spring or early fall can mean faster appointments and sometimes lower pricing.
Questions to Ask Before Approving the Work
Ask what diagnostic testing is included, what the initial leakage reading was, and what reduction the contractor expects. Find out about warranty options and whether a follow-up verification visit is included or billed separately.
Expected Job Duration and Verification Results
Most whole-house Aeroseal jobs take two to seven hours, depending on home size and duct complexity. A reputable contractor will run a final verification test and show you before-and-after leakage numbers in writing.
Frequently Asked Questions
How much does Aeroseal duct sealing typically cost?
Most Metro Detroit homeowners pay between $600 and $4,500 for whole-house Aeroseal duct sealing. A typical mid-size home costs about $1,200 to $2,800, depending on home size, leakage, and duct accessibility.
What is the average Aeroseal duct sealing cost per square foot?
Aeroseal pricing is usually quoted as a whole-project price, but some contractors estimate about $4 to $12 per linear foot of ductwork sealed. A 2,000 square foot home with a typical duct layout usually costs $1,500 to $2,500 for the full job.
Is Aeroseal duct sealing worth the money?
For homes with real duct leakage, Aeroseal can improve comfort, reduce energy waste, and cut down on dust from leaky seams. It’s most worthwhile when a pre-inspection confirms significant leakage.
How long does Aeroseal duct sealing last?
Aeroseal sealant is designed to last for many years under normal HVAC operation. Longevity depends on the system’s condition and whether the ductwork is damaged or exposed to major temperature swings.
Is Aeroseal duct sealing safe for my home and HVAC system?
The sealant is safe for use inside homes and is applied by trained technicians with specialized equipment. It’s used only inside the ductwork, and a licensed HVAC technician manages the entire process from setup through final testing.
Can Aeroseal duct sealing qualify for tax credits or rebates?
Some Michigan energy efficiency programs and utility rebates occasionally cover part of the cost for duct sealing.
Eligibility rules change often, and not every project qualifies.
Ask your HVAC contractor about current rebate options for energy efficiency upgrades.


